The component 1 and 2 densities were still set to 8 MiB and 4 MiB
respectively, which is incorrect for 16 MiB only configurations.
Change the component 1 density to 16 MiB so that the address space
gets properly mapped to SPI 1. In addition, change the number of
components field (byte 0x15) to 0x00 to indicate 1 flash chip.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Inside the BIOS update, there's 68SCE and 68SCF variants.
Based on Qubes HCL and browsing linux-hardware.org, these are
Probook 6360b and Elitebook 8460p respectively.
I checked the KBC1126 EC Firmwares within the update file, both
use the exact same firmware images. Following-up will be a very
similar but untested port for 6360b.
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
remove unnecessary "continue" command. it's written
at the end of a for loop, where it'll continue anyway
Signed-off-by: Leah Rowe <leah@libreboot.org>
this part of the code *must* return. the for loop
afterwards must not be permitted to execute.
it's unlikely that this would ever occur, unless
perhaps the user is using a very buggy sh.
Signed-off-by: Leah Rowe <leah@libreboot.org>
there are special menuentries just for loading
configs, without handling luks, lvm and whatnot.
it's intended for users of cd/dvd drives. well,
now we support both extlinux and grub, with this patch.
Signed-off-by: Leah Rowe <leah@libreboot.org>
isolinux/syslinux/extlinux config files should all work,
using the syslinux parser function in grub
the current behaviour is to only search for grub.cfg,
so extlinux users can't use the default libreboot setup.
with this change, their systems should hopefully work.
Signed-off-by: Leah Rowe <leah@libreboot.org>
the so-called EFI System Partition (ESP) is used
on many UEFI-based setups. some users may be
migrating to libreboot, so let's support it.
on BIOS setups, it would be e.g.
/boot/syslinux/syslinux.conf
on UEFI setups, it would be e.g.
/boot/EFI/syslinux/syslinux.conf
additionally, support scanning for extlinux.conf
Signed-off-by: Leah Rowe <leah@libreboot.org>
lvm/* is slow to resolve in grub, on some machines,
because grub enumeration is very slow in general.
however, many people will install distros with any
number of lvm configurations, so we should try to
support them.
Signed-off-by: Leah Rowe <leah@libreboot.org>
This reverts commit 20389655e4.
If the user actually has encryption, but has /boot unencrypted,
this will considerably slow down the boot, so the patch has
been reverted.
The patch was originally meant to favour encrypted /boot
setups, but the old behaviour also still works there.
when the user sets up an encrypted machine, grub.cfg
defaults to non-encrypted setups if found, first
this patch reverses the order, deferring to
non-encrypted installations only when encrypted ones
are unavailable
Signed-off-by: Leah Rowe <leah@libreboot.org>
These systems have a report that the unlock utility does not work.
Until there are multiple reports of failed unlocks and a technical
determination of why it doesn't work, they will not be listed as
explicitly unsupported.
As this utility requires access to /dev/mem, the default protections of
Linux and OpenBSD must be relaxed to allow this. Make a note of this in
the instructions.
The old Open Security Training site had a course called Advanced x86:
BIOS and SMM Internals, which had a set of slides outlining the method
to supress SMIs by changing the GBL_SMI_EN bit. Add a reference to it as
this is where I originally learned of this method.
all it did was set -v in the shell, which doesn't yield
very useful results. this is a relic of very old design
in the libreboot build system, that is no longer needed.
Signed-off-by: Leah Rowe <leah@libreboot.org>
lbmk didn't quote certain arguments in commands, or
used ! -z instead of -n, things like that. simple fixes.
Signed-off-by: Leah Rowe <leah@libreboot.org>
most of these are probably redundant, and will never
be called, but lbmk needs to be as safe as possible
under fault conditions. fail early, fail hard.
Signed-off-by: Leah Rowe <leah@libreboot.org>
update/trees wasn't correctly returning non-zero status,
even though it was printing an error message, when git-am
failed. this is due to the way subshells work, and it was
overlooked in previous auditing.
additionally: don't directly copy trees to the destination,
instead patch/reset first, then copy only under normal
condition, just as with single-tree projects.
when running build/roms, the script would continue after
a bad git-am, without exit. this patch fixes it in the
most paranoid way possible. i'm now fairly confident that
lbmk will fail gracefully and efficiently, under error
conditions. this should prevent bad image builds.
Signed-off-by: Leah Rowe <leah@libreboot.org>
install libfreetype-dev, instead of libfreetype6-dev
this still works in debian stable (currently 12.2) but
fixes debian sid, as of 15 November 2023. my test machine
with debian sid could not install libfreetype6-dev, but
could install libfreetype-dev
Signed-off-by: Leah Rowe <leah@libreboot.org>
apparently some people use fat file systems for /boot
on linux systems
this is apparently a thing
it's ridiculous, but also a thing
a user reported they could not boot their t400 because
of those, because they have such a distro installed
on their machine
apparently it was a gentoo user
i don't really care. re-add 1980s dos file system support.
Signed-off-by: Leah Rowe <leah@libreboot.org>
Leah Rowe