--- title: Flashing the Dell Latitude E6430 x-toc-enable: true ... Introduction ============ This guide is for those who want libreboot on their Latitude E6430 while they still have the original Dell firmware present. This guide can also be followed (adapted) if you brick your E6430, and you want to recover it. **The Intel video initialisation is libre, implemented with publicly available source code via libgfxinit, from the coreboot project.** Only the intel GPU variants are supported. The Nvidia GPU variants are untested and should be assumed *broken* by default. Flash chip size {#flashchips} =============== Use this to find out: flashrom -p internal The internal flash size is 12MiB on this board; physically, an 8MiB and 4MiB chip (two chips) but this distinction only matters for external flashing. MAC address {#macaddress} =========== The MAC address is part of the ROM image that you're flashing. You can change it at any time, before or after you've flashed Libreboot; you can also change it in the *Dell* BIOS, if you really want to. This is for the onboard gigabit ethernet device. Refer to [mac\_address.md](../hardware/mac_address.md). It is recommended that you run *nvmutil*. See: [nvmutil usage manual](nvmutil.md) The `nvmutil` software is specifically designed for changing MAC addresses, and it implements a few more safeguards (e.g. prevents multicast/all-zero MAC addresses) and features (MAC address randomisation, ability to correct or intentionally corrupt(disable) GbE sections if you wish, swap GbE parts, etc). - **it is also the only software available for this. Please do not use ich9gen on this board. This is an ivybridge board, not ICH9M.** Intel GPU: libre video initialisation available =============================================== Libreboot uses coreboot's native `libgfxinit` on this platform, for variants with Intel graphics. Libreboot releases after 20230625 will support this board, otherwise you can refer to the [build instructions](../build/) Nvidia GPU: Video BIOS Option ROM required ========================================== UNSUPPORTED. DO NOT BUY THE NVIDIA VARIANT. Only the Intel GPU variants are supported. It is believed that the Nvidia variants still have Intel GPUs in them, configured via hardware mux, but this has not yet been configured or tested in the coreboot code; you should assume that the Nvidia models do not work. How to flash internally (no diassembly) ======================================= Warning for BSD users --------------------- **NOTE (15 October 2023): The util is now called `dell-flash-unlock`, but it was previously called `e6400-flash-unlock`. Links have been updated.** BSD *boots* and works properly on these machines, but take note: Nicholas's [dell-flash-unlock](https://browse.libreboot.org/lbmk.git/plain/util/dell-flash-unlock/dell_flash_unlock.c) utility has been ported to OpenBSD, but *other* BSDs are assumed unsupported for now. The `flashrom` software is available on BSD systems. Libreboot's build system has *itself* not yet been ported to the BSDs, but you can use the flash unlock utility. NOTE: BSD is mentioned above, but the only BSD tested for `dell-flash-unlock` is OpenBSD, as of 15 October 2023. Flashing from Linux ------------------- MAKE SURE you boot with this Linux kernel parameter: `iomem=relaxed` - this disables memory protections, permitting `/dev/mem` access needed by flashrom. The flash is memory mapped and flashrom accesses it via `/dev/mem`. You can flash Libreboot directly from the vendor (Dell) BIOS, without taking the machine apart. It can be done entirely from Linux. It will probably also work on BSD systems, but it has only been testing on Linux thus far. **NOTE (15 October 2023): The util is now called `dell-flash-unlock`, but it was previously called `e6400-flash-unlock`. Links have been updated.** Check `util/dell-flash-unlock` in the `lbmk.git` repository, or in release archives for Libreboot releases from 20230423 onwards. Go in there: cd util/dell-flash-unlock make With this program, you can unlock the flash in such a way where everything is writeable. Information about how to use it is in the `README.md` file which is included in that program's directory, or you can read it online here: Literally just run that program, and do what it says. You run it once, shut down, and then power on the machine. Then run it again to confirm that the flash is unlocked. The source code is intuitive enough that you can easily get the gist of it; it's writing some EC commands and changing some chipset config bits. The EC on this machine is hooked up to the `HDA_SDO` signal, also known as the Flash Descriptor Override (FDO), which disables any flash protection by the IFD. When booted with the FDO set, the original Dell firmware disables all other BIOS write protections such as SMM BIOS lock bits. *Make sure* to make a backup of the original firmware before proceeding to flash; see the instructions below. When you flash it, you can use this command: flashrom -p internal -w libreboot.rom Where `libreboot.rom` is your E6430 ROM. *Make sure* it's the right one. If flashrom complains about multiple flash chips detected, just pick one of them (doesn't matter which one), with the `-C` flag as directed; just pick one, and if it doesn't work, try the next. When you see flashrom say `VERIFIED` at the end, that means the flash was successful. If you don't see that, or you're unsure, please [contact the Libreboot project via IRC](../../contact.md). BACK UP THE FACTORY BIOS ======================== The `-w` option flashes `libreboot.rom`. You may consider *backing up* the original Dell BIOS first, using the -r option: flashrom -p internal -r backup.rom AGAIN: make sure to use `-C` accordingly, if you need to pick a chip (where flashrom has detected multiple chip definitions). Just pick one, any of them will probably work, if not try the next. Do this while in a flashable state, after the 2nd run of `dell-flash-unlock`. Make sure the `backup.rom` file gets backed up to an external storage media, not the E6430 itself. With this method, you can probably flash it within 5 minutes. Again, zero disassembly required! How to flash externally ========================= Refer to [spi.md](spi.md) as a guide for external re-flashing. The SPI flash chip shares a voltage rail with the chipset, which is not isolated using a diode. As a result, powering the flash chip externally may cause the QM77 chipset to partially power up and drive the SPI pins, which can interfere with programmers such as the Raspberry Pi. See [RPi Drive Strength](spi.md#rpi-drive-strength) for a workaround. Have a look online for videos showing how to disassemble, if you wish to externally re-flash.