--- title: HP Compaq Elite 8300 USDT x-toc-enable: true ...
HP Compaq Elite 8300 USDT
| ***Specifications*** | | |---------------------------|---------------------------------------------| | **Manufacturer** | HP | | **Name** | Compaq 8300 Elite USDT | | **Released** | 2012 | | **Chipset** | Intel Q77 | | **CPU** | Intel Sandy/Ivy Bridge (65W max.) | | **Graphics** | Intel HD Graphics or MXM graphics card | | **Memory** | Up to 16GB (2x8GB) | | **Architecture** | x86_64 | | **Intel ME/AMD PSP** | Present, neutered | | **Flash chip** | SOIC-16 16MiB | # Introduction This is a small but powerful desktop using Sandy or Ivy Bridge CPUs (of up to 65W TDP). It has a slot for a discrete MXM graphics card, but that is currently untested. Libreboot has support for this, in the Git repository and release versions after (but not including) 20230423. These features are tested and confirmed working: * Native raminit with both DIMMs (up to 2x8GB) * Libgfxinit textmode and framebuffer on both DisplayPorts and VGA * SeaBIOS and GRUB payloads * External USB2 and USB3 ports: they all work * USB 3.0 SuperSpeed on Linux-libre (rear, 4 ports) * Ethernet * Mini-PCIe WLAN * SATA: 2.5" SSD and optical drive bay * PS/2 keyboard and mouse * S3 suspend and resume, wake using USB keyboard * Headphone output, line out, internal speaker * Wake on LAN * Rebooting Untested (and likely don't work): * mSATA * eSATA * Discrete MXM GPU # Installation ## Internal flashing Internal flashing is possible and very simple on this board: First, make sure the computer is powered off. Remove the top cover. The jumper labelled "FDO" (for Flash Descriptor Override) needs to be shorted. That removes all write protections on this board. We can borrow a shunt from another header on the board: PSWD. It is right next to the SO-DIMM RAM slots. Move it to the FDO header between the quartz crystal (small metal cylinder) and the power cable for the optical drive. ![](https://av.libreboot.org/hp8300usdt/jumper_to_fdo.jpg) Boot into an OS of your choice (that has flashrom support). When using Linux, you need to supply the kernel parameter `iomem=relaxed`. The BIOS should no longer impose any write-protections. You can now use `flashrom -p internal` freely. Take a backup of the original BIOS: flashrom -p internal -r oem_bios This is an Ivy Bridge board which means that a neutered ME image is required if you wish to flash the ME region. Libreboot's build system automatically downloads, neuters (using me_cleaner) and inserts this if compiling from source. If you're using Libreboot release ROM images, the ME image has been scrubbed and you must re-insert it. Use the information on this guide to know how to do that: [Insert binary blobs on Intel Sandybridge/Ivybridge/Haswell platforms](../install/ivy_has_common.md) You can now flash libreboot: flashrom -p internal -w libreboot.rom You can now move the jumper back to its original place. By default, Libreboot applies no write-protection, so updating it can be done without the jumper anyway. ## External flashing Unbricking is possible by external flashing. You first need to remove the optical disk drive and 2.5" HDD/SSD and the metal bracket that supports them. This requires you to open one torx screw in total. The SOIC-16 flash chip is located on the edge of the board near the group of yellow cubes. Follow the [general SPI flashing guide](http://localhost:8080/docs/install/spi.html). ![](https://av.libreboot.org/hp8300usdt/chip+header.jpg) You might need to power the board by plugging it in. In that case, do not connect the Vcc (3v3) pin of the flash chip. Also make sure the board doesn't fully power on (that is, boot). If you don't have a suitable clip, you can also use the ROM_RCVRY header right next to the flash chip. By default only the footprint is present, so you have to solder a pin header of your own. End result can be seen and the pinout can be seen in the photo earlier. Consult the HP service manual (page 241) on how to remove the motherboard from the chassis. If you do this, you have to reapply thermal paste. That might be a good idea anyway, considering how old these are getting