2023-08-16 20:34:21 +00:00
|
|
|
tree="haswell"
|
2023-12-27 15:18:21 +00:00
|
|
|
xarch="i386-elf"
|
2022-11-14 00:51:12 +00:00
|
|
|
payload_seabios="y"
|
coreboot: only run GRUB as a secondary payload
See:
https://codeberg.org/libreboot/lbmk/issues/216
Almost all users will be OK running GRUB, but a
minority of users have experienced a fatal error
pertaining to grub_free() or grub_realloc() (as
my investigation of GRUB sources reveal when grepping
the error reported in the link above).
We don't yet know what the bug is, only that the
error occurs, leading to an effective brick if the
user has GRUB as their primary payload.
So far, it has only been reported on some Intel
SandyBridge-based Dell Latitudes in Libreboot, but
we can't be too sure.
The user reported that memtest86+ passes just fine,
and SeaBIOS works; BIOS GRUB also works, which means
that the bug is likely only in an area of GRUB that
runs specifically on the coreboot payload, so it's
probably a driver in GRUB when running on the metal
rather than BIOS/UEFI.
The build system supports a configuration whereby
SeaBIOS is the primary payload, but GRUB is available
in the SeaBIOS boot select menu, and an additional
configuration is available where GRUB is what SeaBIOS
executes first (while still providing boot select);
both of these are now the *only* configurations
available, on all x86 targets except QEMU.
The QEMU target is fine because if the bug occurs there,
you can just close QEMU and try a different image.
Even after this bug is later identified and fixed,
the GRUB source code is vastly over-engineered and there
are likely many more such bugs. SeaBIOS is a reliable
payload; the code is small and robust. Remember always:
Code
equals
bugs
Therefore, this configuration change is likely going
to be permanent. This will apply in the next release.
Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-05-27 13:24:26 +00:00
|
|
|
payload_seabios_withgrub="y"
|
2022-11-14 00:51:12 +00:00
|
|
|
payload_memtest="y"
|
2024-05-29 22:42:48 +00:00
|
|
|
grub_scan_disk="nvme ahci"
|
make GRUB multi-tree and re-add xhci patches
Re-add xHCI only on haswell and broadwell machines, where
they are needed. Otherwise, keep the same GRUB code.
The xHCI patches were removed because they caused issues
on Sandybridge-based Dell Latitude laptops. See:
https://codeberg.org/libreboot/lbmk/issues/216
The issue was not reported elsewhere, including on the
Haswell/Broadwell hardware where they are needed, but the
build system could only build one version of GRUB.
The older machines do not need xHCI patches, because they
either do not have xHCI patches, or work (in GRUB) because
they're in EHCI mode when running the payload.
So, the problem is that we need the xHCI patches for GRUB
on Haswell/Broadwell hardware, but the patches break
Sandybridge hardware, and we only had the one build of GRUB.
To mitigate this problem, the build system now supports
building multiple revisions of GRUB, with different patches,
and each given coreboot target can say which GRUB tree to use
by setting this in target.cfg:
grubtree="xhci"
In the above example, the "xhci" tree would be used. Some
generic GRUB config has been moved to config/data/grub/
and config/grub/ now looks like config/coreboot/ - also,
the grub.cfg file (named "payload" in each tree) is copied
to the GRUB source tree as ".config", then added to GRUB's
memdisk in the same way, as grub.cfg.
Several other design changes had to be made because of this:
* grub.cfg in memdisk no longer automatically jumps to one
in CBFS, but now shows a menuentry for it if available
* Certain commands in script/trees are disabled for GRUB,
such as *config make commands.
* gnulib is now defined in config/submodule/grub/, instead
of config/git/grub - and this mitigates an existing bug
where downloading gnulib first would make grub no longer
possible to download in lbmk.
The coreboot option CONFIG_FINALIZE_USB_ROUTE_XHCI has been
re-enabled on: Dell OptiPlex 9020 MT, Dell OptiPlex 9020 SFF,
Lenovo ThinkPad T440p and Lenovo ThinkPad W541 - now USB should
work again in GRUB.
The GRUB payload has been re-enabled on HP EliteBook 820 G2.
This change will enable per-board GRUB optimisation in the
future. For example, we hardcode what partitions and LVMs
GRUB scans because * is slow on ICH7-based machines, due
to GRUB's design. On other machines, * is reasonably fast,
for automatically enumerating the list of devices for boot.
Use of * (and other wildcards) could enable our GRUB payload
to automatically boot more distros, with minimal fuss. This
can be done at a later date, in subsequent revisions.
Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-06-01 22:01:30 +00:00
|
|
|
grubtree="xhci"
|