lbmk/util/e6400-flash-unlock
Leah Rowe f49eccee72 util/e6400-flash-unlock: do void on ec_fdo_command
the return value was never used
2023-04-30 14:07:02 +01:00
..
COPYING Add E6400 flash unlock utility 2023-04-19 00:31:33 -06:00
Makefile Add E6400 flash unlock utility 2023-04-19 00:31:33 -06:00
README.md util/e6400-flash-unlock: restore README 2023-04-19 18:40:04 +01:00
e6400_flash_unlock.c util/e6400-flash-unlock: do void on ec_fdo_command 2023-04-30 14:07:02 +01:00

README.md

Dell Latitude E6400 Internal Flashing

This utility allows you to use flashrom's internal programmer to program the entire BIOS flash chip from software while still running the original Dell BIOS, which normally restricts software writes to the flash chip.

TL;DR

Run make to compile the utility, and then run sudo ./e6400_flash_unlock and follow the directions it outputs.

How it works

There are several ways the firmware can protect itself from being overwritten. One way is the Intel Flash Descriptor (IFD) permissions. On Intel systems, the flash image is divided into several regions such as the IFD itself, Gigabit Ethernet (GBE) non-volative memory, Management Engine (ME) firmware, Platform Data (PD), and the BIOS. The IFD contains a section which specifies the read/write permissions for each SPI controller (such as the host system) and each region of the flash, which are enforced by the chipset.

On the Latitude E6400, the host has read-only access to the IFD, no access to the ME region, and read-write access to the PD, GBE, and BIOS regions. In order for flashrom to write to the entire flash internally, the host needs full permissions to all of these regions. Since the IFD is read only, we cannot change these permissions unless we directly access the chip using an external programmer, which defeats the purpose of internal flashing.

However, Intel chipsets have a pin strap that allows the flash descriptor permissions to be overridden depending on the value of the pin at power on, granting RW permissions to all regions. On the ICH9M chipset on the E6400, this pin is HDA_DOCK_EN/GPIO33, which will enable the override if it is sampled low. This pin happens to be connected to a GPIO controlled by the Embedded Controller (EC), a small microcontroller on the board which handles things like the keyboard, touchpad, LEDs, and other system level tasks. Software can send a certain command to the EC, which tells it to pull GPIO33 low on the next boot.

Although we now have full access according to the IFD permissions, we still cannot flash the whole chip, due to another protection the firmware uses. Before software can update the BIOS, it must change the BIOS Write Enable (BIOSWE) bit in the chipset from 0 to 1. However, if the BIOS Lock Enable (BLE) bit is also set to 1, then changing the BIOSWE bit triggers a System Management Interrupt (SMI). This causes the processor to enter System Management Mode (SMM), a highly privileged x86 execution state which operates transparently to the operating system. The code that SMM runs is provided by the BIOS, which checks the BIOSWE bit and sets it back to 0 before returning control to the OS. This feature is intended to only allow SMM code to update the system firmware. As the switch to SMM suspends the execution of the OS, it appears to the OS that the BIOSWE bit was never set to 1. Unfortunately, the BLE bit cannot be set back to 0 once it is set to 1, so this functionality cannot be disabled after it is first enabled by the BIOS.

Older versions of the E6400 BIOS did not set the BLE bit, allowing flashrom to flash the entire flash chip internally after only setting the descriptor override. However, more recent versions do set it, so we may have hit a dead end unless we force downgrade to an older version (though there is a more convenient method, as we are about to see).

What if there was a way to sidestep the BIOS Lock entirely? As it turns out, there is, and it's called the Global SMI Enable (GBL_SMI_EN) bit. If it's set to 1, then the chipset will generate SMIs, such as when we change BIOSWE with BLE set. If it's 0, then no SMI will be generated, even with the BLE bit set. On the E6400, GBL_SMI_EN is set to 1, and it can be changed back to 0, unlike the BLE bit. But there still might be one bit in the way, the SMI_LOCK bit, which prevents modifications to GBL_SMI_EN when SMI_LOCK is 1. Like the BLE bit, it cannot be changed back to 0 once it set to 1. But we are in luck, as the vendor E6400 BIOS leaves SMI_LOCK unset at 0, allowing us to clear GBL_SMI_EN and disable SMIs, bypassing the BIOS Lock protections.

There are other possible protection mechanisms that the firmware can utilize, such as Protected Range Register settings, which apply access permissions to address ranges of the flash, similar to the IFD. However, the E6400 vendor firmware does not utilize these, so they will not be discussed.