123 lines
5.1 KiB
Markdown
123 lines
5.1 KiB
Markdown
---
|
|
title: ThinkPad X60 Tablet Recovery guide
|
|
x-toc-enable: true
|
|
...
|
|
|
|
This section documents how to recover from a bad flash that prevents
|
|
your ThinkPad X60 Tablet from booting.
|
|
|
|
ROM images for this machine are well-tested in libreboot, so bricks are rare.
|
|
The most common cause of a brick is operator error, when flashing a ROM image.
|
|
In *most* cases, the cause will be that there is no bootblock, or an invalid
|
|
one.
|
|
|
|
Brick type 1: bucts not reset. {#bucts_brick}
|
|
==============================
|
|
|
|
You still have Lenovo BIOS, or you had libreboot running and you flashed
|
|
another ROM; and you had bucts 1 set and the ROM wasn't dd'd.\* or if
|
|
Lenovo BIOS was present and libreboot wasn't flashed.
|
|
|
|
There are *2* 64KiB bootblocks possible, in the upper part of the ROM image.
|
|
By default (bucts set to 0), the top one is used. If bucts is set to 1, the
|
|
lower one (the one before the top one) is used. This bootblock is the first
|
|
code that executes, during *romstage* as per coreboot hardware initialization.
|
|
|
|
BUC is short for *Backup Control* and TS is short for *Top Swap*. This is a
|
|
special register on Intel platforms. Lenovo BIOS sets PRx registers, preventing
|
|
software re-flashing, but there is a bug in the protection, allowing everything
|
|
*except* the upper 64KiB from being flashed. By default, coreboot only puts a
|
|
bootblock in the upper region. If you flash such a ROM, while bucts is set to 1,
|
|
the system won't boot because there's not a valid bootblock; this is common if
|
|
you're re-flashing when coreboot is already installed, and you didn't set bucts
|
|
back to 0.
|
|
|
|
When you install on X60/T60 the first time, you set this bucts bit to 1, then
|
|
you re-flash a second time and set it back to 0.
|
|
|
|
In this case, unbricking is easy: reset BUC.TS to 0 by removing that
|
|
yellow cmos coin (it's a battery) and putting it back after a minute or
|
|
two:\
|
|
\
|
|
|
|
\*Those dd commands should be applied to all newly compiled X60 ROM
|
|
images (the ROM images in libreboot binary archives already have this
|
|
applied!):
|
|
|
|
dd if=coreboot.rom of=top64k.bin bs=1 skip=$[$(stat -c %s coreboot.rom) - 0x10000] count=64k
|
|
dd if=coreboot.rom bs=1 skip=$[$(stat -c %s coreboot.rom) - 0x20000] count=64k | hexdump
|
|
dd if=top64k.bin of=coreboot.rom bs=1 seek=$[$(stat -c %s coreboot.rom) - 0x20000] count=64k conv=notrunc
|
|
|
|
(doing this makes the ROM suitable for use when flashing a system that
|
|
still has Lenovo BIOS running, using those instructions:
|
|
<http://www.coreboot.org/Board:lenovo/x60/Installation>.
|
|
|
|
Brick type 2: bad ROM image {#recovery}
|
|
===========================================
|
|
|
|
In this instance, you might have flashed a ROM without the top bootblock copied
|
|
to the lower 64KiB section in the ROM, and you flashed the ROM for the first
|
|
time (from Lenovo BIOS), in which case there is not a valid bootblock.
|
|
|
|
In this scenario, you compiled a ROM that had an incorrect
|
|
configuration, or there is an actual bug preventing your system from
|
|
booting. Or, maybe, you set BUC.TS to 0 and shut down after first flash
|
|
while Lenovo BIOS was running. In any case, your system is bricked and
|
|
will not boot at all.
|
|
|
|
"Unbricking" means flashing a known-good (working) ROM. The problem:
|
|
you can't boot the system, making this difficult. In this situation,
|
|
external hardware (see hardware requirements above) is needed which can
|
|
flash the SPI chip (where libreboot resides).
|
|
|
|
|
|
|
|
Remove those screws:\
|
|
|
|
|
|
Remove the HDD:\
|
|
|
|
|
|
Push keyboard forward to loosen it:\
|
|
|
|
|
|
Lift:\
|
|
|
|
|
|
Remove those:\
|
|
|
|
|
|
|
|
|
|
Also remove that (marked) and unroute the antenna cables:\
|
|
|
|
|
|
For some X60T laptops, you have to unroute those too:\
|
|
|
|
|
|
Remove the LCD extend board screws. Also remove those screws (see blue
|
|
marks) and remove/unroute the cables and remove the metal plate:\
|
|
|
|
|
|
Remove that screw and then remove the board:\
|
|
|
|
|
|
This photo shows the flash location:\
|
|
|
|
|
|
This photo shows an SPI flasher used, with SOIC8 test clip:\
|
|
|
|
|
|
Refer to the external flashing guide:
|
|
|
|
[Externally rewrite 25xx NOR flash via SPI protocol](spi.md)
|
|
|
|
NOTE: Do not use the 3.3v rail from your SPI programmer. Leave that disconnected.
|
|
For 3.3v, plug your charger into the mainboard (but do not power on the mainboard)
|
|
when the clip is connected. Before removing the clip, disconnect the charger.
|
|
This will provide adequate 3.3v DC at correct current levels. The SPI flash on an
|
|
X60 Tablet shares a common 3.3V rail with many other components on the mainboard,
|
|
which all draw a lot of current, more than most flashers can provide.
|
|
|
|
Reverse the steps to re-assemble your system, after you've flashed the chip.
|