200 lines
8.6 KiB
Markdown
200 lines
8.6 KiB
Markdown
---
|
|
title: ASUS KCMA-D8 desktop/workstation board
|
|
x-toc-enable: true
|
|
...
|
|
|
|
Introduction
|
|
============
|
|
|
|
Specifications available here:
|
|
<https://www.asus.com/uk/Commercial-Servers-Workstations/KCMAD8/>
|
|
|
|
Quite a nice board; can have up to 16 Opteron 4200/4300 CPU cores, with up to
|
|
64GiB of RAM. It holds its own against more modern machines, especially when
|
|
compiling large source trees (for compilers, what you want is high RAM and more
|
|
CPU cores).
|
|
|
|
This is a desktop board using AMD hardware (Fam10h *and Fam15h* CPUs
|
|
available). It can also be used for building a high-powered workstation.
|
|
libreboot also supports it. The coreboot port was done by Timothy Pearson of
|
|
Raptor Engineering Inc. and, working with them, merged into libreboot many
|
|
years ago.
|
|
|
|
Note that not all boards are compatible. See [board status](#boardstatus)
|
|
below to determine compatibility with your board.
|
|
|
|
Flashing instructions can be found at
|
|
[../install/](../install/) - note that external
|
|
flashing is required (e.g. RPi), if the proprietary (ASUS) firmware is
|
|
currently installed. If you already have Libreboot or coreboot, by default
|
|
it is possible to re-flash using software running in Linux on the kcma-d8,
|
|
without using external hardware.
|
|
|
|
If you currently have the ASUS firmware, please ignore the above link and
|
|
instead refer to the section below:
|
|
|
|
Flashing
|
|
========
|
|
|
|
The default ASUS firmware write-protects the flash, so you have to remove the
|
|
chip and re-flash it using external hardware.
|
|
|
|
It has a 25XX NOR flash (SPI protocol) in a P-DIP 8 socket, which looks like
|
|
this:
|
|
|
|
|
|
|
|
The default chip is a 2MiB one, but we recommend upgrading it to a 16MiB chip.
|
|
|
|
NOTE: If you're already running libreboot, you probably don't
|
|
need to re-flash externally. Refer instead to the generic instructions on
|
|
this page: [../install/](../install/)
|
|
|
|
Refer to the following guide:\
|
|
[Externally rewrite 25xx NOR flash via SPI protocol](../install/spi.md)
|
|
|
|
PCI option ROMs
|
|
===============
|
|
|
|
Unlike Libreboot 20160907, Libreboot in newer releases now supports finding and
|
|
loading PCI option ROMs automatically, both in GRUB and SeaBIOS on this machine.
|
|
This was inherited by libreboot, when the Libreboot project was forked.
|
|
|
|
So for example, if you wish to use an add-on graphics card, you can! It's no
|
|
problem, and should work just fine.
|
|
|
|
CPU coolers
|
|
===========
|
|
|
|
With some creativity, standard AM3+ coolers will work fine.
|
|
|
|
2 x Socket C32 (LGA1207) available, so you can use 2 CPUs. (up to 32GiB per CPU)
|
|
|
|
CPU compatibility
|
|
=================
|
|
|
|
- Opteron 4100 series: Incompatible
|
|
- Opteron 4200 series: Compatible
|
|
- Opteron 4300 series: Compatible
|
|
|
|
Board status (compatibility) {#boardstatus}
|
|
============================
|
|
|
|
There are two ways to identify a supported KCMA-D8 board:
|
|
|
|
1. Serial number (sticker attached to the 24-pin ATX power connector)
|
|
2. BIOS version (sticker next to CPU slot 1, last four digits)
|
|
|
|
Supported boards begin with a serial number of **B9S2xxxxxxxx** or above where
|
|
the first character refers to the year of manufacture (A = 2010, B = 2011, etc.)
|
|
and the following character the month in hexadecimal (1...9, A, B, C). Thus, any
|
|
board produced September 2011 *or later* are compatible with libreboot. Boards
|
|
originally shipped with BIOS version **2001** or higher are also compatible.
|
|
|
|
For help locating these identifying markers, see [ASUS documentation for determining Opteron 4200 series compatibility](https://web.archive.org/web/20200710022605/https://dlcdnets.asus.com/pub/ASUS/mb/SocketC%281027%29/KCMA-D8/Manual&QVL/How_to_identify_MB_supporting_Opteron_4200_CPU.pdf)
|
|
|
|
For more detailed information regarding the coreboot port, see
|
|
<https://raptorengineeringinc.com/coreboot/kcma-d8-status.php>
|
|
|
|
Form factor {#formfactor}
|
|
===========
|
|
|
|
This board is ATX form factor. While the [ATX standard, version 2.2](https://web.archive.org/web/20120725150314/http://www.formfactors.org/developer/specs/atx2_2.pdf)
|
|
specifies board dimensions 305mm x 244mm, this board measures 305mm x 253mm;
|
|
please ensure that your case supports this extra ~cm in width.
|
|
|
|
IPMI iKVM module add-on {#ipmi}
|
|
=======================
|
|
|
|
Don't use it. It uses proprietary firmware and adds a backdoor (remote
|
|
out-of-band management chip, similar to the [Intel Management
|
|
Engine](../../faq.md#intelme). Fortunately, the firmware is
|
|
unsigned (possible to replace) and physically separate from the
|
|
mainboard since it's on the add-on module, which you don't have to
|
|
install.
|
|
|
|
Flash chips {#flashchips}
|
|
===========
|
|
|
|
2MiB flash chips are included by default, on these boards. It's on a
|
|
P-DIP 8 slot (SPI chip). The flash chip can be upgraded to higher sizes:
|
|
4MiB, 8MiB or 16MiB. With at least 8MiB, you could feasibly fit a
|
|
compressed linux+initramfs image (BusyBox+Linux system) into CBFS and
|
|
boot that, loading it into memory (and nowadays there is LinuxBoot, for which
|
|
we would recommend a 16MiB boot flash)
|
|
|
|
*DO NOT hot-swap the chip with your bare hands. Use a P-DIP 8 chip
|
|
extractor. These can be found online. See
|
|
<http://www.coreboot.org/Developer_Manual/Tools#Chip_removal_tools>*
|
|
|
|
Ideally, you should not hot-swap. Only remove the IC when the system is
|
|
powered down and disconnected from mains.
|
|
|
|
Native graphics initialization {#graphics}
|
|
==============================
|
|
|
|
Only text-mode is known to work, but linux(kernel) can initialize the
|
|
framebuffer display (if it has KMS - kernel mode setting).
|
|
|
|
NOTE: This section relates to the onboard ASpeed GPU. You *can* use an add-on
|
|
PCI-E GPU in one of the available slots on the mainboard. Nvidia GTX 780 cards
|
|
are what libreboot recommends; it has excellent support in Nouveau (free Linux
|
|
kernel / mesa driver for Nvidia cards) and generally works well; however, the
|
|
performance won't be as high in Nouveau, compared to the non-free Nvidia driver
|
|
because the Nouveau driver can't increase the GPU clock (it doesn't know how,
|
|
as of 18 March 2021).
|
|
|
|
Current issues {#issues}
|
|
==============
|
|
|
|
- Opteron 4100 series CPUs are currently incompatible
|
|
- LRDIMM memory modules are currently incompatible
|
|
(use UDIMMs please)
|
|
- Memory initialization is still problematic for some modules. We
|
|
recommend avoiding Kingston and Super Talent modules for this reason.
|
|
|
|
The coreboot wiki has some information about RAM compatibility. The wiki is
|
|
deprecated but the info on it is still correct for this board. Some other
|
|
considerations:
|
|
|
|
- Booting from USB mass storage devices is currently broken under GRUB.
|
|
Consequently, the textmode ROM with SeaBIOS is recommended otherwise
|
|
in order to install an operating system you will need a hard disk with
|
|
a pre-installed OS or will have to plug in another HDD or CD/DVD
|
|
reader in order to boot OS installation media.
|
|
- SeaBIOS lacked serial console support out-of-the-box in release 20160907
|
|
and as such a workaround using SGABIOS is necessary. You can find
|
|
instructions on how to do this on the
|
|
[Notabug issue tracker](http://web.archive.org/web/20210416011941/https://notabug.org/libreboot/libreboot/issues/736)
|
|
TODO: test whether this is still the case in libreboot, which uses a newer
|
|
version of coreboot nowadays)
|
|
- SAS (via PIKE 2008 module) requires non-free option ROM (and
|
|
SeaBIOS) to boot from it (theoretically possible to replace, but you
|
|
can put a kernel in CBFS or on SATA and boot from that, which
|
|
can be on a SAS drive. The linux kernel can use those SAS drives
|
|
(via PIKE module) without an option ROM).
|
|
NOTE: SeaBIOS can load PCI-E option ROMs, and by default it will do so in
|
|
libreboot, so you could use it. However, you could *also* simply
|
|
install 16MiB NOR flash with linuxboot payload in it, and use linuxboot
|
|
which has the Linux kernel, which can use SAS drives without needing that
|
|
option ROM; then it can kexec another linux kernel, which in turn also can
|
|
can use those drives. Or just put a standard linux kernel and initramfs
|
|
in cbfs and chainload that from GRUB, with the right parameters.
|
|
- IPMI iKVM module (optional add-on card) uses proprietary firmware.
|
|
Since it's for remote out-of-band management, it's theoretically a
|
|
backdoor similar to the Intel Management Engine. Fortunately, unlike
|
|
the ME, this firmware is unsigned which means that a free
|
|
replacement is theoretically possible. For now, the libreboot
|
|
project recommends not installing the module. [This
|
|
project](https://github.com/facebook/openbmc) might be interesting
|
|
to derive from, for those who want to work on a free replacement. In
|
|
practise, out-of-band management isn't very useful anyway (or at
|
|
the very least, it's not a major inconvenience to not have it).
|
|
- Graphics: only text-mode works. See [\#graphics](#graphics)
|
|
|
|
Hardware specifications {#specifications}
|
|
-----------------------
|
|
|
|
Check the ASUS website.
|
|
|