reduce the number of calls to read() by using
bit shifts. when rnum is zero, read again. in
most cases, a nibble will not be zero, so this
will usually result in about 13-15 of of 16
nibbles being used. this is in comparison to
8 nibbles being used before, which means that
the number of calls to read() are roughly
halved. at the same time, the extra amount of
logic is minimal (and probably less) when
compiled, outside of calls to read(), because
shifting is better optimised (on 64-bit machines,
the uint64_t will be shifted with just a single
instruction, if the compiler is decent), whereas
the alternative would be to always precisely use
exactly 16 nibbles by counting up to 16, which
would involve the use of an and mask and still
need a shift, plus...
you get the point. this is probably the most
efficient code ever written, for generating
random numbers between the value of 0 and 15
some checks check for specific utils, which are
then used to indicate the existence of other utils,
which means that building them singularly, as is
currently done, may result in errors later if another
tool doesn't exist compiled yet
this is an obscure bug, fixed by this patch. more of a
workaround really. a dirty hack. when checking for any
of the coreboot utilities required, build all coreboot
utilities that are possibly required
the utilities are small enough that this does not add
much extra time to build, and in most cases, all of them
will be needed anyway
U-Boot can be configured via environment variables which can be saved to
various storage devices. This usually defaults to MMC or SPI depending
on where it boots from, but assumes the device's layout is controlled by
U-Boot.
We should store the environment in SPI flash, but we also need to
configure coreboot FMAPs to reserve the area U-Boot would use as its
environment storage. For now, disable environment storage by setting
ENV_IS_NOWHERE=y to avoid overwriting random regions of SPI or MMC if
someone tries to save the variables.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Set default U-Boot revision to v2023.01 and rebase patches on top of
that. Upstream kconfig status is a bit unstable, so updating configs
with `make oldconfig` would miss important upstream changes.
For each board, run `make savedefconfig` and `diffconfig -m` at the old
version to get a diff from upstream defconfigs. Fix those affected by
upstream changes, like SYS_TEXT_BASE being renamed to TEXT_BASE. Then
append those to the new version's defconfigs and run `make olddefconfig`
to get updated configs.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
the way nvmutil is designed, setWord() is only ever called
under non-error conditions. however, if one part is valid but
the other one isn't, and a command is run that touches both parts,
errno is non-zero write writeGbeFile is called
in situations where one part is valid, but the other isn't, AND the
writes to gbe (in memory) results in a non-change, writeGbeFile is
not called; in this situation, errno is not being reset, despite
non-error condition
this patch fixed the bug, resulting in zero status upon exit under
such conditions
the current code writes part 1 first, and part 0 next,
on the disk, due to the way the swap works.
with this change, swap still swaps the two parts of the file,
on disk, but writes the new file sequentially.
this change might speed up i/o on the file system, on HDDs.
on SSDs, this change likely makes no difference at all.
On many Lenovo GbE regions (in factory firmware), part 0 is
invalid but part 1 is valid.
This change means part 1 is checked first. If part 1 is valid,
part 0 won't be checked at all (due to how most C compilers
optimise).
Most people are just going to extract the factory GbE file,
modify it and re-insert it into the ROM image, so this causes
a nice speedup.
don't constantly open/close the file: /dev/urandom
only read 12 bytes at a time
because of this change, the readFromFile() function now only
handles gbe files
The USB 2.0 ports on Exynos boards need the relevant driver enabled by
USB_EHCI_EXYNOS. This is enabled by default depending on USB_EHCI_HCD.
It's already enabled on snow and spring, but apparently not on peach
boards, as discovered from other people's attempts to enable it [1][2].
Enable it also on the peach_pi and peach_pit.
[1] 8f12e43dbf
[2] 11cacf55ad
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
The display driver on the veyron boards needs reset drivers, more
specifically RESET_ROCKCHIP. This is enabled by default depending on
DM_RESET, which an upstream commit enables for veyron_jerry claiming it
fixes the display [1]. Enable it also in our configs, but for other
veyrons as well.
[1] https://lore.kernel.org/u-boot/20220928024046.2657593-1-sjg@chromium.org/
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
By making lbmk fully POSIX-compliant, it will be easier to port lbmk to
other systems implementing POSIX such as Alpine Linux and FreeBSD.
Signed-off-by: Ferass 'Vitali64' EL HAFIDI <vitali64pmemail@protonmail.com>
Leah Rowe