458 lines
20 KiB
Markdown
458 lines
20 KiB
Markdown
# Porting coreboot using autoport
|
|
|
|
## Supported platforms
|
|
|
|
### Chipset
|
|
For any Sandy Bridge or Ivy Bridge platform the generated result should
|
|
be bootable, possibly with minor fixes.
|
|
|
|
### EC / SuperIO
|
|
EC support is likely to work on Intel-based thinkpads. Other laptops are
|
|
likely to miss EC support. SuperIO support on desktops is more likely to
|
|
work out of the box than any EC.
|
|
|
|
## How to use autoport
|
|
|
|
Enable as many devices as possible in the firmware setup of your system.
|
|
This is useful to detect as many devices as possible and make the port
|
|
more complete, as disabled devices cannot be detected.
|
|
|
|
Boot into target machine under any Linux-based distribution and install
|
|
the following tools on it:
|
|
* `gcc`
|
|
* `golang`
|
|
* `lspci`
|
|
* `dmidecode`
|
|
* `acpidump` (part of `acpica` on some distros)
|
|
|
|
Clone the coreboot tree and `cd` into it. For more detailed steps, refer
|
|
to Rookie Guide, Lesson 1. Afterwards, run these commands:
|
|
|
|
cd util/ectool
|
|
make
|
|
cd ../inteltool
|
|
make
|
|
cd ../superiotool
|
|
make
|
|
cd ../autoport
|
|
go build
|
|
sudo ./autoport --input_log=logs --make_logs --coreboot_dir=../..
|
|
|
|
Note: in case you have problems getting gcc and golang on the target
|
|
machine, you can compile the utilities on another computer and copy
|
|
the binaries to the target machine. You will still need the other
|
|
listed programs on the target machine, but you may place them in the
|
|
same directory as autoport.
|
|
|
|
Check for unknown detected PCI devices, e.g.:
|
|
|
|
Unknown PCI device 8086:0085, assuming removable
|
|
|
|
If autoport says `assuming removable`, you are fine. If it doesn't,
|
|
you may want to add the relevant PCI IDs to autoport. Run `lspci -nn`
|
|
and check which device this is using the PCI ID. Devices which are not
|
|
part of the chipset, such as GPUs or network cards, can be considered
|
|
removable, whereas devices inside the CPU or the PCH such as integrated
|
|
GPUs and bus controllers (SATA, USB, LPC, SMBus...) are non-removable.
|
|
|
|
Your board has now been added to the tree. However, do not flash it
|
|
in its current state. It can brick your machine. Instead, keep this
|
|
new port and the logs from `util/autoport/logs` somewhere safe. The
|
|
following steps will back up your current firmware, which is always
|
|
recommended, since coreboot may not boot on the first try.
|
|
|
|
Disassemble your computer and find the flash chip(s). Since there could be
|
|
more than one, this guide will refer to "flash chips" as one or more chips.
|
|
Refer to <https://flashrom.org/Technology> as a reference. The flash chip is
|
|
usually in a `SOIC-8` (2x4 pins, 200mil) or `SOIC-16` (2x8 pins) package. As
|
|
it can be seen on flashrom's wiki, the former package is like any other 8-pin
|
|
chip on the mainboard, but it is slightly larger. The latter package is much
|
|
easier to locate. Always make sure it is a flash chip by looking up what its
|
|
model, printed on it, refers to.
|
|
|
|
There may be a smaller flash chip for the EC on some laptops, and other chips
|
|
such as network cards may use similar flash chips. These should be left as-is.
|
|
If in doubt, ask!
|
|
|
|
Once located, use an external flasher to read the flash chips with `flashrom -r`.
|
|
Verify with `flashrom -v` several times that reading is consistent. If it is not,
|
|
troubleshoot your flashing setup. Save the results somewhere safe, preferably on
|
|
media that cannot be easily overwritten and on several devices. You may need this
|
|
later. The write process erases the flash chips first, and erased data on a flash
|
|
chip is lost for a very long time, usually forever!
|
|
|
|
Compile coreboot for your ported mainboard with some console enabled. The most
|
|
common ones are EHCI debug, serial port and SPI flash console as a last resort.
|
|
If your system is a laptop and has a dedicated video card, you may need to add
|
|
a video BIOS (VBIOS) to coreboot to be able to see any video output. Desktop
|
|
video cards, as well as some MXM video cards, have this VBIOS on a flash chip
|
|
on the card's PCB, so this step is not necessary for them.
|
|
|
|
Flash coreboot on the machine. On recent Intel chipsets, the flash space is split
|
|
in several regions. Only the one known as "BIOS region" should be flashed. If
|
|
there is only one flash chip present, this is best done by adding the `--ifd`
|
|
and `-i bios` parameters flashrom has (from v1.0 onwards) to specify what flash
|
|
descriptor region it should operate on. If the ME (Management Engine) region is
|
|
not readable, which is the case on most systems, use the `--noverify-all`
|
|
parameter as well.
|
|
|
|
For systems with two flash chips, this is not so easy. It is probably better to
|
|
ask in coreboot or flashrom communication channels, such as via IRC or on the
|
|
mailing lists.
|
|
|
|
Once flashed, try to boot. Anything is possible. If a log is generated, save it
|
|
and use it to address any issues. See the next section for useful information.
|
|
Find all the sections marked with `FIXME` and correct them.
|
|
|
|
Send your work to review.coreboot.org. I mean it, your effort is very appreciated.
|
|
Refer to Rookie Guide, Lesson 2 for instructions on how to submit a patch.
|
|
|
|
## Manual fixes
|
|
### SPD
|
|
In order to initialize the RAM memory, coreboot needs to know its timings, which vary between
|
|
modules. Socketed RAM has a small EEPROM chip, which is accessible via SMBus and contains the
|
|
timing data. This data is usually known as SPD. Unfortunately, the SMBus addresses may not
|
|
correlate with the RAM slots and cannot always be detected automatically. The address map is
|
|
encoded in function `mainboard_get_spd` in `romstage.c`. By default, autoport uses the most
|
|
common map `0x50, 0x51, 0x52, 0x53` on everything except for Lenovo systems, which are known
|
|
to use `0x50, 0x52, 0x51, 0x53`. To detect the correct memory map, the easiest way is to boot
|
|
on the vendor firmware with just one module in channel 0, slot 0, and check the SMBus address
|
|
the EEPROM has. Under Linux, you can use these commands to see what is on SMBus:
|
|
|
|
$ sudo modprobe i2c-dev
|
|
$ sudo modprobe i2c-i801
|
|
$ sudo i2cdetect -l
|
|
i2c-0 i2c i915 gmbus ssc I2C adapter
|
|
i2c-1 i2c i915 gmbus vga I2C adapter
|
|
i2c-2 i2c i915 gmbus panel I2C adapter
|
|
i2c-3 i2c i915 gmbus dpc I2C adapter
|
|
i2c-4 i2c i915 gmbus dpb I2C adapter
|
|
i2c-5 i2c i915 gmbus dpd I2C adapter
|
|
i2c-6 i2c DPDDC-B I2C adapter
|
|
i2c-7 i2c DPDDC-C I2C adapter
|
|
i2c-8 i2c DPDDC-D I2C adapter
|
|
i2c-9 smbus SMBus I801 adapter at 0400 SMBus adapter
|
|
|
|
$ sudo i2cdetect 9
|
|
WARNING! This program can confuse your I2C bus, cause data loss and worse!
|
|
I will probe file /dev/i2c-9.
|
|
I will probe address range 0x03-0x77.
|
|
Continue? [Y/n] y
|
|
0 1 2 3 4 5 6 7 8 9 a b c d e f
|
|
00: -- -- -- -- -- 08 -- -- -- -- -- -- --
|
|
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
|
|
20: -- -- -- -- 24 -- -- -- -- -- -- -- -- -- -- --
|
|
30: 30 31 -- -- -- -- -- -- -- -- -- -- -- -- -- --
|
|
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
|
|
50: 50 -- -- -- 54 55 56 57 -- -- -- -- 5c 5d 5e 5f
|
|
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
|
|
70: -- -- -- -- -- -- -- --
|
|
|
|
Make sure to replace the `9` on the last command with the bus number for SMBus on
|
|
your system. Here, there is a module at address `0x50`. Since only one module was
|
|
installed on the first slot of the first channel, we know the first position of
|
|
the SPD array must be `0x50`. After testing all the slots, your `mainboard_get_spd`
|
|
should look similar to this:
|
|
|
|
void mainboard_get_spd(spd_raw_data *spd) {
|
|
read_spd(&spd[0], 0x50);
|
|
read_spd(&spd[1], 0x51);
|
|
read_spd(&spd[2], 0x52);
|
|
read_spd(&spd[3], 0x53);
|
|
}
|
|
|
|
Note that there should be one line per memory slot on the mainboard.
|
|
|
|
Note: slot labelling may be missing or unreliable. Use `inteltool` to see
|
|
which slots have modules in them.
|
|
|
|
This procedure is ideal, if your RAM is socketed. If you have soldered RAM,
|
|
remove any socketed memory modules and check if any EEPROM appears on SMBus.
|
|
If this is the case, you can proceed as if the RAM was socketed. However,
|
|
you may have to guess some entries if there multiple EEPROMs appear.
|
|
|
|
Most of the time, soldered RAM does not have an EEPROM. Instead, the SPD data is
|
|
inside the main flash chip where the firmware is. If this is the case, you need
|
|
to generate the SPD data to use with coreboot. Look at `inteltool.log`. There
|
|
should be something like this:
|
|
|
|
/* SPD matching current mode: */
|
|
/* CH0S0 */
|
|
00: 92 11 0b 03 04 00 00 09 03 52 01 08 0a 00 80 00
|
|
10: 6e 78 6e 32 6e 11 18 81 20 08 3c 3c 00 f0 00 00
|
|
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 65 00
|
|
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 6d 17
|
|
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
/* CH1S0 */
|
|
00: 92 11 0b 03 04 00 00 09 03 52 01 08 0a 00 80 00
|
|
10: 6e 78 6e 32 6e 11 18 81 20 08 3c 3c 00 f0 00 00
|
|
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 65 00
|
|
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 6d 17
|
|
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
|
|
This is not a full-fledged SPD dump, as it only lists
|
|
the currently-used speed configuration, and lacks info
|
|
such as a serial number, vendor and model. Use `xxd`
|
|
to create a binary file with this SPD data:
|
|
|
|
$ cat | xxd -r > spd.bin <<EOF
|
|
00: 92 11 0b 03 04 00 00 09 03 52 01 08 0a 00 80 00
|
|
10: 6e 78 6e 32 6e 11 18 81 20 08 3c 3c 00 f0 00 00
|
|
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 65 00
|
|
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 6d 17
|
|
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
EOF (press Ctrl + D)
|
|
|
|
Then, move the generated file into your mainboard's directory
|
|
and hook it up to the build system by adding the following
|
|
lines to `Makefile.mk`:
|
|
|
|
cbfs-files-y += spd.bin
|
|
spd.bin-file := spd.bin
|
|
spd.bin-type := raw
|
|
|
|
Now we need coreboot to use this SPD file. The following example
|
|
shows a hybrid configuration, in which one module is soldered and
|
|
the other one is socketed:
|
|
|
|
void mainboard_get_spd(spd_raw_data *spd)
|
|
{
|
|
void *spd_file;
|
|
size_t spd_file_len = 0;
|
|
/* C0S0 is a soldered RAM with no real SPD. Use stored SPD. */
|
|
spd_file = cbfs_boot_map_with_leak("spd.bin", CBFS_TYPE_RAW,
|
|
&spd_file_len);
|
|
if (spd_file && spd_file_len >= 128)
|
|
memcpy(&spd[0], spd_file, 128);
|
|
|
|
/* C1S0 is a physical slot. */
|
|
read_spd(&spd[2], 0x52);
|
|
}
|
|
|
|
If several slots are soldered there are two ways to handle them:
|
|
|
|
* If all use the same SPD data, use the same file for all the slots. Do
|
|
not forget to copy the data on all the array elements that need it.
|
|
* If they use different data, use several files.
|
|
|
|
If memory initialization is not working, in particular write training (timB)
|
|
on DIMM's second rank fails, try enabling rank 1 mirroring, which can't be
|
|
detected by inteltool. It is described by SPD field "Address Mapping from Edge
|
|
Connector to DRAM", byte `63` (`0x3f`). Bit 0 describes Rank 1 Mapping,
|
|
0 = standard, 1 = mirrored; set it to 1. Bits 1-7 are reserved.
|
|
|
|
### `board_info.txt`
|
|
|
|
`board_info.txt` is a text file used in the board status page to list all
|
|
the supported boards and their specifications. Most of the information
|
|
cannot be detected by autoport. Common entries are:
|
|
|
|
* `ROM package`, `ROM protocol` and `ROM socketed`:
|
|
These refer to the flash chips you found earlier. You can visit
|
|
<https://flashrom.org/Technology> for more information.
|
|
|
|
* `Release year`: Use the power of Internet to find that information.
|
|
* `Category`: This describes the type of mainboard you have.
|
|
Valid categories are:
|
|
* `desktop`. Desktops and workstations.
|
|
* `server`. Servers.
|
|
* `laptop`. Laptops, notebooks and netbooks.
|
|
* `half`. Embedded / PC/104 / Half-size boards.
|
|
* `mini`. Mini-ITX / Micro-ITX / Nano-ITX
|
|
* `settop`. Set-top-boxes / Thin clients.
|
|
* `eval`. Development / Evaluation Boards.
|
|
* `sbc`. Single-Board computer.
|
|
* `emulation`: Virtual machines and emulators. May require especial care
|
|
as they often behave differently from real counterparts.
|
|
* `misc`. Anything not fitting the categories above. Not recommended.
|
|
|
|
* `Flashrom support`: This means whether the internal programmer is usable.
|
|
If flashing coreboot internally works, this should be set to `y`. Else,
|
|
feel free to investigate why it is not working.
|
|
|
|
### `USBDEBUG_HCD_INDEX`
|
|
|
|
Which controller the most easily accessible USB debug port is. On Intel,
|
|
1 is for `00:1d.0` and 2 is for `00:1a.0` (yes, it's reversed). Refer to
|
|
<https://www.coreboot.org/EHCI_Debug_Port> for more info.
|
|
|
|
If you are able to use EHCI debug without setting the HCD index manually,
|
|
this is correct.
|
|
|
|
### `BOARD_ROMSIZE_KB_2048`
|
|
|
|
This parameter refers to the total size of the flash chips coreboot will be in.
|
|
This value must be correct for S3 resume to work properly. This parameter also
|
|
defines the size of the generated coreboot image, but that is not a major issue
|
|
since tools like `dd` can be used to cut fragments of a coreboot image to flash
|
|
on smaller chips.
|
|
|
|
This should be detected automatically, but it may not be detected properly in
|
|
some cases. If it was not detected, put the correct total size here to serve
|
|
as a sane default when configuring coreboot.
|
|
|
|
### `DRAM_RESET_GATE_GPIO`
|
|
|
|
When the computer is suspended to RAM (ACPI S3), the RAM reset signal must not
|
|
reach the RAM modules. Otherwise, the computer will not resume and any opened
|
|
programs will be lost. This is done by powering down a MOSFET, which disconnects
|
|
the reset signal from the RAM modules. Most manufacturers put this gate on GPIO
|
|
60 but Lenovo is known to put it on GPIO 10. If suspending and resuming works,
|
|
this value is correct. This can also be determined from the board's schematics.
|
|
|
|
## GNVS
|
|
|
|
`mainboard_fill_gnvs` sets values in GNVS, which then ACPI makes use of for
|
|
various power-related functions. Normally, there is no need to modify it
|
|
on laptops (desktops have no "lid"!) but it makes sense to proofread it.
|
|
|
|
## `gfx.ndid` and `gfx.did`
|
|
|
|
Those describe which video outputs are declared in ACPI tables.
|
|
Normally, there is no need to have these values, but if you miss some
|
|
non-standard video output, you can declare it there. Bit 31 is set to
|
|
indicate the presence of the output. Byte 1 is the type and byte 0 is
|
|
used for disambigution so that ID composed of byte 1 and 0 is unique.
|
|
|
|
Types are:
|
|
* 1 = VGA
|
|
* 2 = TV
|
|
* 3 = DVI
|
|
* 4 = LCD
|
|
|
|
## `c*_acpower` and `c*_battery`
|
|
|
|
Which mwait states to match to which ACPI levels. Normally, there is no
|
|
need to modify anything unless your device has very special power saving
|
|
requirements.
|
|
|
|
## `install_intel_vga_int15_handler`
|
|
|
|
This is used with the Intel VGA BIOS, which is not the default option.
|
|
It is more error-prone than open-source graphics initialization, so do
|
|
not bother with this until your mainboard boots. This is a function
|
|
which takes four parameters:
|
|
1. Which type of LCD panel is connected.
|
|
2. Panel fit.
|
|
3. Boot display.
|
|
4. Display type.
|
|
|
|
Refer to `src/drivers/intel/gma/int15.h` to see which values can be used.
|
|
For desktops, there is no LCD panel directly connected to the Intel GPU,
|
|
so the first parameter should be `GMA_INT15_ACTIVE_LFP_NONE`. On other
|
|
mainboards, it depends.
|
|
|
|
## CMOS options
|
|
|
|
Due to the poor state of CMOS support in coreboot, autoport does not
|
|
support it and this probably won't change until the format in the tree
|
|
improves. If you really care about CMOS options:
|
|
|
|
* Create files `cmos.layout` and `cmos.default`
|
|
* Enable `HAVE_OPTION_TABLE` and `HAVE_CMOS_DEFAULT` in `Kconfig`
|
|
|
|
## EC (lenovo)
|
|
|
|
You need to set `has_keyboard_backlight` (backlit keyboard like X230),
|
|
`has_power_management_beeps` (optional beeps when e.g. plugging the cord
|
|
in) and `has_uwb` (third MiniPCIe slot) in accordance to functions available
|
|
on your machine
|
|
|
|
In rare cases autoport is unable to detect GPE. You can detect it from
|
|
dmesg or ACPI tables. Look for line in dmesg like
|
|
|
|
ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
|
|
|
|
This means that GPE is `0x11` in ACPI notation. This is the correct
|
|
value for `THINKPAD_EC_GPE`. To get the correct value for `GPE_EC_SCI`
|
|
you need to substract `0x10`, so value for it is `1`.
|
|
|
|
The pin used to wake the machine from EC is guessed. If your machine doesn't
|
|
wake on lid open and pressing of Fn, change `GPE_EC_WAKE`.
|
|
|
|
Keep `GPE_EC_WAKE` and `GPE_EC_SCI` in sync with `gpi*_routing`.
|
|
`gpi*_routing` matching `GPE_EC_WAKE` or `GPE_EC_SCI` is set to `2`
|
|
and all others are absent.
|
|
|
|
If your dock has LPC wires or needs some special treatement you may
|
|
need to add codes to initialize the dock and support code to
|
|
DSDT. See the `init_dock()` for `x60`, `x200` or `x201`.
|
|
|
|
## EC (generic laptop)
|
|
|
|
Almost any laptop has an embedded controller. In a nutshell, it's a
|
|
small, low-powered computer designed to be used on laptops. Exact
|
|
functionality differs between machines. Its main functions include:
|
|
|
|
* Control of power and rfkill to different component
|
|
* Keyboard (PS/2) interface implementation
|
|
* Battery, AC, LID and thermal information exporting
|
|
* Hotkey support
|
|
|
|
autoport automatically attempts to restore the dumped config but it
|
|
may or may not work and may even lead to a hang or powerdown. If your
|
|
machine stops at `Replaying EC dump ...` try commenting EC replay out
|
|
|
|
autoport tries to detect if machine has PS/2 interface and if so calls
|
|
`pc_keyboard_init` and exports relevant ACPI objects. If detection fails
|
|
you may have to add them yourself
|
|
|
|
ACPI methods `_PTS` (prepare to sleep) and `_WAK` (wake) are executed
|
|
when transitioning to sleep or wake state respectively. You may need to
|
|
add power-related calls there to either shutdown some components or to
|
|
add a workaround to stop giving OS thermal info until next refresh.
|
|
|
|
For exporting the battery/AC/LID/hotkey/thermal info you need to write
|
|
`acpi/ec.asl`. For an easy example look into `apple/macbook21` or
|
|
`packardbell/ms2290`. For information about needed methods consult
|
|
relevant ACPI specs. Tracing which EC events can be done using
|
|
[dynamic debug](https://wiki.ubuntu.com/Kernel/Reference/ACPITricksAndTips)
|
|
|
|
EC GPE needs to be routed to SCI in order for OS in order to receive
|
|
EC events like "hotkey X pressed" or "AC plugged". autoport attempts
|
|
to detect GPE but in rare cases may fail. You can detect it from
|
|
dmesg or ACPI tables. Look for line in dmesg like
|
|
|
|
ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
|
|
|
|
This means that GPE is `0x11` in ACPI notation. This is the correct
|
|
value for `_GPE`.
|
|
|
|
Keep GPE in sync with `gpi*_routing`.
|
|
`gpi*_routing` matching `GPE - 0x10` is set to `2`
|
|
and all others are absent. If EC has separate wake pin
|
|
then this GPE needs to be routed as well
|