export LBMK_VERSION_TYPE=x
x can be: stable, unstable
in target.cfg files, specify:
status=x
x can be: stable, unstable, broken, untested
if unset, lbmk defaults to "unknown"
if LBMK_VERSION_TYPE is set, no confirmation is asked
if the given target matches what's set (but what's set
in that environmental variable can only be stable or
unstable)
if LBMK_RELEASE="y", no confirmation is asked, unless
the target is something other than stable/unstable
"unstable" means it works, but has a few non-breaking
bugs, e.g. broken s3 on dell e6400
whereas, if raminit regularly fails or it is so absolutely
unreliable as to be unusable, then the board should be
declared "broken"
untested means: it has not been tested
With this change, it should now be easier to track whether
a given board is tested, in preparation for releases. When
working on trees/boards, status can be set for targets.
Also: in the board directory, you can add a "warn.txt" file
which will display a message. For example, if a board has a
particular quirk to watch out for, write that there. The message
will be printed during the build process, to stdout.
If status is anything *other* than stable, or it is unstable
but LBMK_VERSION_TYPE is not set to "unstable", and not building
a release, a confirmation is passed.
If the board is not specified as stable or unstable, during
a release build, the build is skipped and the ROM is not
provided in that release; this is in *addition* to
release="n" or release="y" that can be set in target.cfg,
which will skip the release build for that target if "n"
Signed-off-by: Leah Rowe <leah@libreboot.org>
On T60 with Libreboot 20231106 and the GRUB payload, a user
reported this error in GRUB when a battery was connected:
"alloc magic is broken at 0x7b1aedf0: 0"
This error disappears when a battery is not connected, or
when using Libreboot 20230625. The issue has persisted
through to LIbreboot 20240225 and after, and I believe the
issue will be somewhere in coreboot, not in GRUB itself.
For now, switch i945 laptops (X60, T60, Macbook2,1) back to
the February 2023 coreboot revision used in Libreboot 20230625.
A bisect can be done before the next Libreboot release, ETA
May 2024, if time permits. Otherwise, this revert should solve
the problem for now, at least so far as Libreboot is concerned.
The following coreboot patches have been backported:
commit 29030d0f3dad2ec6b86000dfe2c8e951ae80bf94
Author: Bill Xie <persmule@hardenedlinux.org>
Date: Sat Oct 7 01:32:51 2023 +0800
drivers/pc80/rtc/option.c: Stop resetting CMOS during s3 resume
Further patches from upstream:
commit 432e92688eca0e85cbaebca3232f65936b305a98
Author: Bill Xie <persmule@hardenedlinux.org>
Date: Fri Nov 3 12:34:01 2023 +0800
drivers/pc80/rtc/option.c: Reset only CMOS range covered by checksum
These patches fixed S3 on GM45 machines, though it will be useful on
the i945 machines aswell.
The reason I'm doing it this way it is because I don't have a battery
for my X60 or T60, and my T60 isn't in a very good state either,
so I can't reproduce the error myself yet.
Signed-off-by: Leah Rowe <leah@libreboot.org>
i added mkukri's patch but didn't enable it. this was intentional.
this patch enables tpm by default, on all 9020 sff/mt targets.
most users probably won't need it, but enabling it won't hurt.
Signed-off-by: Leah Rowe <leah@libreboot.org>
at present, the inject scripts compress refcode in a way
that is not reproducible, so there's no way to verify
that the firmware is correct, via checksum verification,
when injecting vendor code on release images
the lack of reproducibility in recompression will have to be
addressed, but the issue is that lbmk does not provide its own
sources for compression utilities, instead opting to use the
system's own compression utility
so the solution might be for lbmk not to use the host's utility,
and compile its own, or insert the refcode uncompressed. for now,
simply disable the hp 820 g2 target in libreboot releases
this uses the same logic recently implemented for excluding
mrc-based haswell images in libreboot releases
Signed-off-by: Leah Rowe <leah@libreboot.org>
release="n" is set in target.cfg on haswell build targets
that use mrc.bin
script/update/release exports LBMK_RELEASE="y"
script/build/roms skips building a given target if release="n"
in target.cfg *and* LBMK_RELEASE="y"
you could also do the export yourself before running ./build roms,
for example:
export LBMK_RELEASE="y"
./build roms all
This would skip these ROM images. The native haswell raminit is
now stable enough in my testing, that I wish to delete the MRC-based
targets. This is in line with Libreboot's Binary Blob Reduction Policy,
which states: if a blob can be avoided, it should be avoided.
The problem is that users often run the inject script in *lbmk* from
Git, instead of from the src release archive. I forsee some users
running this on modern lbmk with older release images. If the mrc-based
target isn't there, the user may use an NRI-based target name, and
think it works; they will insert without MRC. I foresaw this ages
ago, which is why Caleb and I ensured that the script checks hashes,
and hashes are included in releases.
Therefore: for the time being, keep the MRC-based configs in lbmk
but do not include images for them in releases. This can be done
indefinitely, but I'll probably remove those configs entirely at
some point.
On the following boards, Libreboot now will *only* provide NRI-based
ROM images for the following machines:
* Dell OptiPlex 9020 SFF
* Dell OptiPlex 9020 MT
* Lenovo ThinkPad T440p
* Lenovo ThinkPad W541/W540
I now recommend exclusive use of NRI-based images, on Haswell
hardware. It's stable enough in my testing, and now supports S3.
Signed-off-by: Leah Rowe <leah@libreboot.org>
sff happened to work, but mt would not boot with the patch,
because it called die() on unknown chassis type, and the gpio
happened to have a bad value in the old patch, because it wasn't
reading the right gpio.
i tested the fix on the old patch, but then decided to use
mate's new patch because instead of calling die(), it simply
boots with fan control disabled (max fan speed in that case),
if this happens again.
mt and sff have both been tested with this new version of the
patch. both of them boot, and they both have proper fan control.
Signed-off-by: Leah Rowe <leah@libreboot.org>
a hangover from earlier days, but i still disable it. i forgot
to do so on this config, when updating the nri code. do it now.
Signed-off-by: Leah Rowe <leah@libreboot.org>
hell added a patch fixing S3 on haswell NRI, but it seems
you still need to set 8MB CBFS size as with the MRC
tested on a t440p. S3 now works on haswell NRI.
Signed-off-by: Leah Rowe <leah@libreboot.org>
the t440p/w541 configs were re-done from scratch, because
the coreboot revisions are nearly two years apart.
i also added corebootfb configs.
hell updated their patchset. this patchset uses the following patch:
https://review.coreboot.org/c/coreboot/+/81948/1
it uses this, along with parent patches in the haswell nri patch series
Signed-off-by: Leah Rowe <leah@libreboot.org>
see:
https://review.coreboot.org/c/coreboot/+/81529
what i've merged is patchset 4. i had to rebase it slightly,
because the libreboot version has the iommu toggle on cmos
configs, which are files that mate's patch also changes,
leading to merge conflict.
Signed-off-by: Leah Rowe <leah@libreboot.org>
the grub payload was previously disabled, because the libre
mrc code sets up xhci rather than ehci, and grub did not have
xhci support (not natively).
libreboot now has xhci support in the grub payload, so enable
grub on these configurations.
Signed-off-by: Leah Rowe <leah@libreboot.org>
broadwell mrc enables both igpu and dgpu to be enabled
at any given time. if the onboard (intel) gpu is set as
primary, the logic to disable it is not executed within
coreboot; instead, the igpu is used for vga decode.
on some t440p/w541 thinkpads, both an intel and nvidia
gpu are present. in this setup, the intel gpu must be
used for vga, and all output, but rendering can be
offloaded to the nvidia gpu (nvidia optimus).
optimus would never work on haswell mrc.bin, because it
always disables the igpu when a dgpu is present, so a hack
exists in coreboot that hides the dgpu from mrc, so that the
igpu remains enabled. broadwell mrc doesn't do this, so the
option to hide PEG devices has been disabled in these
configs.
the broadwell mrc has better peg device handling, and can
support 16gb modules on broadwell hardware; it may well
support these modules on haswell hardware too, though ddr3
sodimms are very hard to find (and expensive). (and currently
untested, with this patch)
Signed-off-by: Leah Rowe <leah@libreboot.org>
broadwell mrc has better peg handling and can support 16gb
modules on broadwell machines - the blob can be used on haswell
machines too, instead of haswell mrc, and it might support 16gb
modules on these machines (not yet tested, but using broadwell
mrc does at least boot as reliably as haswell mrc anyway)
one little quirk with haswell mrc is that it actually handles
vga decode, disabling the igpu entirely, when a dgpu is used.
the broadwell mrc enables both GPUs and does not handle vga
decoding, so we must handle this the usual way; my patch for
this was merged upstream and i'm also adding it to libreboot,
which currently uses an older coreboot revision. this is needed
for dgpu to work. see patch:
0040-nb-haswell-Disable-iGPU-when-dGPU-is-used.patch
broadwell mrc may also make dealing with nvidia optimus setups
more reliable, on laptops that have nvidia GPUs, but this patch
does not add bmrc configs for t440p/w541
NOTE: on t440p/w541 laptops with nvidia graphics, the video output
is wired to intel but rendering can be offloaded to nvidia. in this
setup, we want vga decode to be done on intel, so i've set these
configs to enable CONFIG_ONBOARD_VGA_IS_PRIMARY (set it to y)
Signed-off-by: Leah Rowe <leah@libreboot.org>
3rd sata slot (of 3) broken on 9020 sff, and the 3rd and 4th (of 4)
slots are broken on 9020 mt
this patch fixes them on both, so that all ports work properly
Signed-off-by: Leah Rowe <leah@libreboot.org>
Needed to make graphics cards work. Turn it on if you're using
only the Intel GPU.
With IOMMU *enabled*, graphics cards do not work reliably at all.
The cause still needs to be investigated, but the symptoms are
graphical corruption on the screen, and Xorg usually crashes.
In some cases (on some cards), TTYs can still be used; the payload
can still be used reliably, on a graphics card, but Xorg fails to
work properly.
This could be a bug in Linux drivers, instead of anything that
coreboot does (not yet tested in factory BIOS).
Leaving it off by default will ensure reliable operation on all
setups, whether an iGPU or dGPU is used.
Signed-off-by: Leah Rowe <leah@libreboot.org>
It is now possible to disable the IOMMU on Haswell
boards, by doing this on your ROM image:
./nvramtool -C libreboot.rom -w iommu=Disable
To enable it again, do this:
./nvramtool -C libreboot.rom -w iommu=Enable
If not specified, the default behaviour is *on*.
A follow-up patch will turn IOMMU *off* by default,
on Dell OptiPlex 9020 SFF/MT, by setting it as such
in cmos.default. This is to make graphics cards work
properly to work around a bug when it's turned on.
Leaving the IOMMU enabled is recommended, if it works.
It works in most cases, including on 9020 SFF/MT when
using the Intel GPU without a graphics card inserted.
Signed-off-by: Leah Rowe <leah@libreboot.org>
Iru Cai's port from Gerrit:
https://review.coreboot.org/c/coreboot/+/39398
Now with the proper MXM structure, which removes the 30 second POST
delay. Tested with i7-2670QM, Quadro 2000M and 32GB RAM.
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
The OptiPlex 9020/7020 port was merged first and was numbered 31.
Increment the numbering of the Latitude patches to reflect this.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
i enabled it but it's buggy according to comments on gerrit.
disable for now. dgpu didn't work anyway, even with it turned
off, when i had this tested.
Signed-off-by: Leah Rowe <leah@libreboot.org>
keep dell9020mt_12mb
dell9020mtvga_12mb doesn't actually work (was tried for
running a graphics card on its own, with no igpu init)
Signed-off-by: Leah Rowe <leah@libreboot.org>
this was done automatically by running:
./update trees -u coreboot
this has to be done when adding patches for now board ports,
because of the way lbmk and also coreboot's build systems work.
the configs just have to be re-generated to include a line
that says the entry for the newly added boards isn't set. look
at the diff of this commit as an example.
Signed-off-by: Leah Rowe <leah@libreboot.org>
on a dgpu setup, igpu was still in use, when tested
by a user. do separate roms that don't enable anything
vga in coreboot, relying instead only on seabios to
execute a vga rom. these roms will only work if you
have a graphics card.
Signed-off-by: Leah Rowe <info@minifree.org>
Specifically the MT versions. The SFF versions will
be added separately, in a later commit.
See: https://review.coreboot.org/c/coreboot/+/55232
This patch has been added, from patchset 31. It still
has some unresolved issues, on that patchset, but
it should boot. See commit message there.
Of note: I've enabled PCI REBAR, though it's unknown
whether it will work (some comments there about it though,
on that gerrit page).
I've also set CBFS size to 8MB, not the full size of
the BIOS region; this is required on the T440p which
uses the same mrc.bin file, to get S3 working.
TSEG stage cache disabled, as on other Haswell boards.
The setup: SeaBIOS-only as first payload, but with GRUB
enabled as secondary payload. The _grubonly setup has
been enabled here. This way, the config will work on
iGPU and dGPU setups without issue.
Signed-off-by: Leah Rowe <info@minifree.org>
coreboot gerrit patch 55232, patchset 31
the actual board will be enabled in a follow-up patch.
merging the patch on its own first is better practise,
to run ./update trees -u coreboot
this way, there won't be a revision that breaks builds,
due to the idiosyncratic nature of coreboot configuration.
Signed-off-by: Leah Rowe <info@minifree.org>
CONFIG_PS2M_EISAID. this is a a string used for the
identifier on the mouse, in ACPI.
CONFIG_PS2K_EISAID this is used for the keyboard.
IASL comes back with this build error:
dsdt.asl 1884: Name(_HID, EISAID("DLLK0534"))
Error 6045 - ^ EISAID string must be of the form "UUUXXXX" (3 uppercase, 4 hex digits) (DLLK0534)
Change DLLK0534 back to PNP0303 and
change DLL0534 back to PNP0F13. These are generic identifiers
for PS/2 keyboard and mouse. Any generic driver will work with
the onboard mouse/keyboard on these machines. They do not need
to be changed. These are the default values anyway. Just leave
them explicitly defined to the default values, for now; if these
options are not set, coreboot will default to these values.
This shouldn't break anything for the users. I've reported this
to Nicholas Chin, author of those patches. Libreboot imported
the new versions of E6430/E6530 board patches in the coreboot
revision update, but the new (technically correct) values broke
IASL, so I've decided to use the old values for now.
Signed-off-by: Leah Rowe <leah@libreboot.org>
re-use the same patches, and drop the same patches.
this tree uses hell's special ddr2 fix, which we apply
for the dell latitude e6400.
Signed-off-by: Leah Rowe <leah@libreboot.org>
Base revision changed to:
commit b6cbfa977f63d57d5d6b9e9f7c1cef30162f575a
Author: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Date: Fri Jan 5 16:48:17 2024 +0800
mb/google/dedede/var/metaknight:Add fw_config probe for multi codec
and amplifier
Of note:
Several out-of-tree ports have been adjusted to use the new SPD config
style, where it is defined in devicetree. I manually updated the E6530
patch myself, based on the update that Nicholas did on E6430 (Nicholas
will later update the E6530 patch himself, and I'll re-merge the patch).
Several upstream patches now exist in this revision, that we were able
to remove from lbmk.
The heap size patch was reverted upstream, as we did, but see:
https://review.coreboot.org/c/coreboot/+/80023https://review.coreboot.org/c/coreboot/+/79525
Although we still disable the TSEG Stage Cache, ivy/sandy/haswell should
be reliable on S3 now (leaving TSEG Stage Cache disabled, for now, anyway).
Also included in upstream now:
commit 29030d0f3dad2ec6b86000dfe2c8e951ae80bf94
Author: Bill Xie <persmule@hardenedlinux.org>
Date: Sat Oct 7 01:32:51 2023 +0800
drivers/pc80/rtc/option.c: Stop resetting CMOS during s3 resume
Further patches from upstream:
commit 432e92688eca0e85cbaebca3232f65936b305a98
Author: Bill Xie <persmule@hardenedlinux.org>
Date: Fri Nov 3 12:34:01 2023 +0800
drivers/pc80/rtc/option.c: Reset only CMOS range covered by checksum
This should fix S3 on GM45 thinkpads.
Signed-off-by: Leah Rowe <leah@libreboot.org>
these should be using the rdimm tree for crossgcc,
so define it explicitly. the build system creates
a symlink too, but it's still best that we use it.
Signed-off-by: Leah Rowe <leah@libreboot.org>
in a build test, canoeboot 0.1 builds, but master doesn't,
and neither does lbmk. i changed a few of them when doing
the crossgcc build optimisation patches.
i'm just copying the configs from there. unlike in the
canoeboot version of this patch, i've re-enabled microcode
updates in these lbmk configs.
Signed-off-by: Leah Rowe <leah@libreboot.org>
a tree can specify:
tree_depend="treename"
this will make the other tree be downloaded. this is
used for coreboot trees, to ensure that dependency
trees are downloaded, because trees can now re-use
crossgcc from other trees.
Signed-off-by: Leah Rowe <leah@libreboot.org>
with neutered ME, fan control fails. while there are
ways to mitigate it, many users will not, and will
likely see their system overheat, which is very
dangerous.
this bug (failed fan control on neutered ME) only
affects arrandale machines such as lenovo x201.
the newer machines are not affected by this.
other arrandale machines will probably not be added
to libreboot because of this, or they will be subject
to further testing.
Signed-off-by: Leah Rowe <leah@libreboot.org>
This is of Broadwell platform, one generation above Haswell.
Of note: this uses HP Sure Start. Although the flash is 16MB,
our CBFS section (and IFD configuration) assumes 12MB flash,
so the final 4MB will be left unflashed on installation,
after blanking the private flash. The coreboot documents have
more information about this.
Some minor design changes in lbmk were made, to accomodate
this port:
Support for extracting refcode binaries added (pulled from
Google recovery images). The refcode file is an ELF that
initialises the MRC and the PCH. It is also responsible for
enabling or disabling the Intel GbE device, where Google
does not enable it, but lbmk modifies it per the instructions
on the coreboot documentation, so as to enable Intel GbE.
Google's recovery image stores the refcode as a stage file,
but coreboot changed the format (for CBFS files) after 4.13
so coreboot 4.13's cbfstool is used to extract refcode. This
realisation made me also change the script logic to use a
cbfstool and ifdtool version matching the coreboot tree, for
all parts of lbmk, whereas lbmk previously used only the
default tree for cbfstool/ifdtool, on insertion and deletion
of vendor files - it was 81dc20e744 that broke extraction of
refcode on google's recovery images, where google used an older
version of cbfstool to insert the files in their coreboot ROMs.
A further backported patch has been added, copying coreboot
revision f22f408956 which is a build fix from Nico Huber.
Iru Cai submitted an ACPI bugfix after the revision lbmk
currently uses, for coreboot/default, and this fix is
needed for rebooting to work on Linux 6.1 or higher. This
patch has been backported to lbmk, while it still uses the
same October 2023 revision of coreboot.
Broadwell MRC is inserted at the same offset as Haswell,
so I didn't need to tweak that.
Signed-off-by: Leah Rowe <leah@libreboot.org>
arch no longer needs to be set, on multi-tree projects,
and it has been renamed to xarch
the new behaviour is: if xarch is set, treat it as a
list of crossgcc targets and go through the list. set
the first one as the target, for what lbmk builds, but
build all of the defined crossgccc targets
crossgcc_ada is now xlang, and defines which languages
to build, rather than whether to build gcc-gnat
Signed-off-by: Leah Rowe <leah@libreboot.org>
i had to run make-oldconfig on all of them, because
of the port that riku added the other day. lbmk doesn't
use defconfigs, it uses full configs, so we have to
make sure they're kept in sync
this patch is the result of running the following command
in a fresh clone of lbmk:
./update trees -u coreboot
i should probably switch to defconfigs.
Signed-off-by: Leah Rowe <leah@libreboot.org>
the e6400_4mb target has libgfxinit and (if seabios) vgarom
initialisation, but has issues on the nvidia model, even when
using nomodeset. with this target, e6400nvidia_4mb, only
the vgarom initialisation is used, libgfxinit is disabled.
on nvidia models, this one should work a little bit better.
specifically: nouveau crashes on this machine, with libreboot
installed, but you can use nomodeset. however, when libgfxinit
is also enabled, nomodeset no longer works properly.
so this target disables all video initialisation in coreboot.
only seabios will initialise anything video-related, by
executing the vga option rom.
Signed-off-by: Leah Rowe <leah@libreboot.org>
at present, lbmk can remove microcode updates on images for
a given target, if the target specifies
microcode_required="n" in target.cfg
lbmk then provides images with microcode, and images without,
in a given release. although the user can also remove them
manually, this just makes it a bit more convenient, for those
users who do wish to run without the updates. this functionality
is provided only on those platforms where no-microcode is tested.
well, this behaviour implements a compromise on libreboot policy,
which is to always include microcode updates by default. see:
Binary Blob Reduction Policy
the *canoeboot* project now exists, developed in parallel with
libreboot, and it ships without microcode updates, on the same
targets where lbmk also handled this.
running without microcode updates is foolish, and should not
be encouraged. clean up lbmk by not providing this kludge.
the libreboot documentation will be updated, telling such users
to try canoeboot instead, or to remove the update from a given
libreboot rom - this is still possible, and mitigations such as
PECI disablement on GM45 are still in place (and will be kept),
so that this continues to work well.
Signed-off-by: Leah Rowe <leah@libreboot.org>
this affects 8460p and 8470p only, as the others' updates
aren't common across different boards
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
don't handle "romtype" at all, in board target.cfg files
add /dev/null as pike2008 rom on amd boards. this serves
the same purpose, adding them as empty vga roms, to add
an empty rom in cbfs. pike2008 cards cause seabios to hang,
when their oproms are executed, so we insert a fake rom
on i945 thinkpads, use the coreboot config option:
CONFIG_INTEL_ADD_TOP_SWAP_BOOTBLOCK
when set, this enables the same bootblock copy, for use
with bucts. these two cases, namely pike2008 roms and
i945 bootblock copies, no longer need to be handled in code
Signed-off-by: Leah Rowe <leah@libreboot.org>
the x220 edp patch invalidated lots of configs, so
i did: ./update trees -u coreboot
this is the resulting patch
Signed-off-by: Leah Rowe <leah@libreboot.org>
only call crossgcc for coreboot and u-boot, but use
hostcc for everything else. simplify the checking of
which architecture to compile for. "arch" in target.cfg
files has been modified, to allow further simplification.
without this patch, the logic currently only *barely* avoids
using crossgcc on things like utils, and only works in practise
because, in practise, lbmk only works on x86_64 anyway.
the new logic, as per this patch, is simpler and more robust.
Signed-off-by: Leah Rowe <leah@libreboot.org>
Inside the BIOS update, there's 68SCE and 68SCF variants.
Based on Qubes HCL and browsing linux-hardware.org, these are
Probook 6360b and Elitebook 8460p respectively.
I checked the KBC1126 EC Firmwares within the update file, both
use the exact same firmware images. Following-up will be a very
similar but untested port for 6360b.
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
Fix a few issues with the E6430 configs to make it consistent with
configs for other boards and function as intended.
- Add VBT to CBFS: Although the VBT was enabled at the board level
Kconfig in a previous commit (CONFIG_INTEL_GMA_HAVE_VBT), the config
to actually add the VBT to CBFS was still unset.
- Enable the static option table: The old config would always use the
fallback values hard coded in the coreboot tree, rather than the
settings in the cmos.default file
- Enable DRAM clear on boot: This was not set previously, even though
most other boards set this for security.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
TSEG Stage Cache enabled again, because disabling it
did not affect S3 in any way.
Many configs have changed, and debug level is set to 7.
In testing with V-T60 on IRC, it wasn't just removal of
the DDR2 patch that I did, but I re-did the configs too,
in exactly the same way I've done them here, when testing
on an X200 to fix boot issues.
Libreboot does not use defconfigs, instead it uses full
configs, and these have to be updated. I normally just
run make-oldconfig on every config, for revision updates.
However, every now and then, we need to re-do them.
Play it safe and re-do every config. I've double- and
triple-checked that the configs are correct.
Signed-off-by: Leah Rowe <leah@libreboot.org>
the ddr2 fix broke *ddr3* on gm45 thinkpads in
testing, depending on memory modules. this was
established by removing patches, re-doing
configs etc, on a user's X200 (testing gentoo
and freebsd). the X200 kept randomly rebooting
or having random glitches.
the configs themselves (gm45 thinkpads) will
also be re-done, because i found minor issues
unrelated, but this patch moves dell e6400 to
its own tree. the ddr2 fix is no longer present
in coreboot/default, only coreboot/dell.
i noticed minor differences in gm45 thinkpad
configs, when re-doing the configs, versus
what are currently in lbmk master; for instance,
vbt was not enabled anymore, on thinkpad x200.
modifications to these will be done separately.
Signed-off-by: Leah Rowe <leah@libreboot.org>
The original E6430 patch included the Intel VBT file, but did not
actually enable it in Kconfig. Update the patch to enable it and
update the E6430 configs.
it didn't work in the past, but it does work nowadays;
specifically, it only worked with libgfxinit in the past,
but not on VGA ROMs.
now it does work on VGA ROMs, tested on e6400 and t1650 so
it was enabled there.
in this setup, a special image is provided where SeaBIOS is
the main payload, but it only loads GRUB; nothing else, every.
this is called SeaGRUB. this setup is useful in cases where
the user only has a GPU that lacks libgfxinit support.
Signed-off-by: Leah Rowe <leah@libreboot.org>
it's preferable that the vram setting be as high as
feasible, for users. we overlooked this on some
newer platforms that were added, over several
releases. these levels won't offend most users,
and people who want less can always turn it down
Signed-off-by: Leah Rowe <leah@libreboot.org>
My previous fix to revert didn't fix S3 on GM45, one
of the platforms reported fixed by 78263; I'm merging
that instead, at patch set 10.
It is referenced by 78815/1 which was split from it,
so merge that too (restores overrides of higher values,
on certain platforms that we don't use yet).
https://review.coreboot.org/c/coreboot/+/78623/10https://review.coreboot.org/c/coreboot/+/78815/1
Accordingly, update configs to match the new default.
Signed-off-by: Leah Rowe <leah@libreboot.org>
also, enable seabios_withgrub on e6400, but not grubfirst;
right now, we also support dgpu which would brick on
grubfirst. on my tested nvidia model, loading grub from
seabios worked, so i'm going to re-add seabios_grubfirst
functionality like in older libreboot revisions, enabled
selectively on a given target.
e6430 currently only has igpu support anyway, but i've done
the same thing there, in anticipation of future dgpu support.
e6400 and e6430 ec report scancode set 2 with translation
by default, but only actually output scancode set 1
grub is trying to use scancode set 2 without scancode
translation, so the key inputs get messed up
fix it by forcing scancode set 2 with translation, but
only on coreboot; other build targets on GRUB will
retain the same behaviour as before
courtesy goes to Nicholas Chin who inspired me, and
helped me to fix this. tested on Nicholas's E6400
and E6430, and my E6400; Riku also tested it on
non-Dell, as did I (some thinkpads), and all seems OK.
The new behaviour in coreboot GRUB is essentially no
different to that of SeaBIOS, which does the same.
Signed-off-by: Leah Rowe <leah@libreboot.org>
the patch included in this revision is pulled from:
https://review.coreboot.org/c/coreboot/+/54024/2
contrary to hell's assertion of "not for merge", this does
in fact work nicely on a dell e6400; nicholas chin tested
on e6400 and found that those RCOMP values are the same
nicholas was testing some errant modules that seemed to
fail raminit in coreboot. in some cases, dell e6400 would
regularly fail coldboot even though reboot was ok; this was
therefore the cause of suspicioun for it being raminit-related
with this patch from hell (Angel Pons, but knows as hell
on IRC) it should fix boot issue on Dell Latitude E6400
Signed-off-by: Leah Rowe <leah@libreboot.org>
note: me6_update_parser needs to be written, similar
to me7_update_parser, to generate the partition
tables within intel me6 on lenovo bios updates.
the current logic in lbmk goes like this:
mkdir -p vendorfiles/cache/
and save your factory dump as:
vendorfiles/cache/x201_factory.rom
the build system has been modified, in such a way
as to support extracting me.bin (which is the full
one) and then neutering from this.
this is done automatically, if the file is present,
but you must first insert that file there, which means
you'll need a dump of the original boot flash on your
thinkpad x201
Signed-off-by: Leah Rowe <leah@libreboot.org>
the patch:
https://review.coreboot.org/c/coreboot/+/78270
this has been reverted, because it caused s3 resume
issues on most intel laptops in libreboot.
i was going to merge this instead:
https://review.coreboot.org/c/coreboot/+/78623
however, it's under review, and this doesn't change
to the old behaviour; it keeps the new universal
config, but changes the default
we know the old logic works, so keep that for now.
in fact, the offending patch was only merged to
main in coreboot, one day before i recently
updated coreboot revs in coreboot/default - i used
a 12 october revision, the patch above is 11 october
i then ran "./update trees -u coreboot" which updated
the heap sizes back to the old defaults. this should
fix s3 suspend/resume where it was broken, in the
libreboot 20231021 release - a point release with this
and a few other fixes is planned soon.
Signed-off-by: Leah Rowe <leah@libreboot.org>
the logic for naming coreboot roms is based on whether
cpu_microcode_blob.bin would exist in cbfs, and whether
deletion was therefore successful.
lbmk was naming nomicrocode on fam15h roms on this basis,
but the microcode was being inserted as microcode_amd.bin
and microcode_amd_fam15h.bin
in the recent 20231021 release, the roms were exclusively
labeled _nomicrocode in the rom names, but they do in fact
contain microcode.
i'm fixing it by telling lbmk *not* to delete microcode.
if microcode_required is not set, or it's set to y, then
only roms *with* microcode updates are provided; even if
the rom doesn't actually contain it, lbmk will only label
it _nomicrocode if that setting is set to n.
i'm not bothering to add further complexity to the rom
handling logic, because canoeboot now exists anyway (at
website https://canoeboot.org/) which is my new version
re-implementing the older, inferior version of libreboot
so i'm going to:
1) document this as errata in the release
2) cross reference in the freedom status page
3) if someone still isn't happy, i'll say use canoeboot
job done.
Signed-off-by: Leah Rowe <leah@libreboot.org>
Add a U-Boot build for the qemu_x86_12mb board. The config is a copy of
the upstream "coreboot" defconfig, but with OF_EMBED=y.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
github's httpd b0rked the fuck out and i didn't want to wait
for them to fix it (ssl cert error) before i continued a build.
i now host the relevant acpica tarball on libreboot rsync,
mirrored to princeton.
Signed-off-by: Leah Rowe <leah@libreboot.org>
as opposed to the current 3-level structure.
recent build system simplifications have enabled
this change, thus:
./build fw coreboot -> ./build roms
./build fw grub -> ./build grub
./build fw serprog -> ./build serprog
./update project release -> ./update release
./update project trees -> ./update trees
./update vendor download -> ./vendor download
./update vendor inject -> ./vendor inject
alper criticised that the commands were too long,
so i made them shorter!
Signed-off-by: Leah Rowe <leah@libreboot.org>
i previously added this just for kicks, but it's not
actually needed; gnat isn't used on fam15h boards so
lbmk doesn't even use it (it's disabled).
in fact, i tested lbmk with crossgcc_ada handling
taken out, but with said patch; i still got build
errors with gnat anyway, on that old coreboot
revision (but gnat isn't needed there anymore).
Signed-off-by: Leah Rowe <leah@libreboot.org>
We don't really need a custom coreboot tree for Chromebooks. I had added
one, because at a cursory glance to the available config/coreboot/board
subdirectories I had the impression that I should. But upstreams have
one tree for every board and I think we should move towards that too.
Move the one important BL31 makefile patch into the default coreboot
patches, update the gru boards' configs by running savedefconfig in the
cros tree and then running olddefconfig in the default tree.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Riku's mSATA patch for HP8300USDT was merged upstream, so the
patch has been dropped from lbmk because it is contained within
this new coreboot revision.
Signed-off-by: Leah Rowe <leah@libreboot.org>
some users reported build errors. technically, there's
nothing wrong with lbmk but it relies on hostcc, and
hostcc is hit or miss when it comes to cross compiling
32-bit, depending on the build system of whatever project.
lbmk needs to handle cross compilation. for now, i'm just
disabling memtest86plus on non-64-bit hosts.
Signed-off-by: Leah Rowe <leah@libreboot.org>
in the future, we may start downloading files that aren't
blobs, such as mxm port configs (on mainboards that use
MXM graphics)
this directory will contain all of those files
generally change the language used, across lbmk, to make
use of "vendorfile" instead of "blob"
Signed-off-by: Leah Rowe <leah@libreboot.org>
Leah Rowe